Superset 4150 user manual

The information is subject to change without notice and should not be construed in any way as a commitment by Mitel Networks; or any of its affiliates or subsidiaries. Mitel Networks and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document.

Revisions of this document or new editions of it may be issued to incorporate any such changes. Nothing in this document may be reproduced in any manner, either wholly or in part for any use whatsoever, without written permission from Mitel Networks Corporation.

All rights reserved. Printed in Canada. This telephone is NOT suitable for direct connection to the public-switched telephone network. Connect the telephone to a Mitel Networks telephone system only.

The personal key on the bottom right is always your Prime Line; the remaining personal keys can be programmed as Feature, Speed Call, or Line Appearance keys. See Feature Keys for personal key programming instructions. Your telephone also features for feature access, an alphanumeric liquid crystal display LCD with contrast control, Handsfree operation, and a large Message Indicator.

Note: When using the SuperKey , press Backup softkey to back up one menu level. See your system administrator for computer-telephony features that may be available to you if your telephone has been connected in this way. Installation will disable your handset microphone. Disconnecting the headset at the jack or at the quickdisconnect plug restores handset operation. Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you cradle the handset between your ear and shoulder.

If you use your phone a lot, you may find it more comfortable to use a headset. See the section on headset usage elsewhere in this guide for more information.

Your phone has a control for adjusting the volume of the handset receiver or headset. Because continuous exposure to loud sounds can contribute to hearing loss, keep the volume at a moderate level. The stand built into your phone tilts to give you a better view of the keys and display.

Press the tilt-release paddle on the telephone base. Tilt your telephone to the desired angle. Release the tilt-release paddle. To remove the handset shipped with your phone from the handset cord:. Bend a paper clip to produce approcimately 4 cm 1. On the handset, locate the plastic groove leading into the handset jack. The groove is on the side of the jack that is closest to the handset microphone. Slide the end of the wire into the handset jack along the groove until it stops underneath the handset cord clip.

While gently pulling on the handset cord, use the wire to pry the clip upward. The cord will separate from the handset. Store the original handset in a safe place. Press the More softkey until the Ring Adjust softkey appears. Table Of Contents. Quick Links. See also: User Manual. User Guide. Table of Contents. Previous Page. Next Page. Mitel Superset User Manual 44 pages. Mitel Superset User Manual 42 pages. Integrated communications platform subattendant user guide 14 pages.

Page 2 The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks x00ae; Corporation. The information is subject to change without notice and should not be construed in any way as a commitment by Mitel Networks or any of its affiliates or subsidiaries.

See your system administrator for computer-telephony features that may be available to you if your telephone has been connected in this way. Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you cradle the handset between your ear and shoulder.

If you use your phone a lot, you may find it more comfortable to use a headset. See the section on headset usage elsewhere in this guide for more information. To remove the handset shipped with your set from the handset cord: 1. Bend a paper clip to produce approximately 4 cm 1. On the handset, locate the plastic groove leading into the handset jack.

Press the More softkey until the Ring Adjust softkey appears. Press a personal key. To re-program a personal key: 1. Press the More softkey until the Display Keys softkey appears. Press the Display Keys softkey. Lift the handset. Dial the number, Press a Speed Call key. Answer a call Lift the handset. Press the flashing Line appearance key and lift the handset. Page Redial Redial To redial the last number that you manually dialed: 1.

Redial - Saved Number To save the last number that you manually dialed: 1. To Redial a saved number: 1. To dial a stored Speed Call number: 1. Dial Enter an index number between 00 and Note: Your system administrator may have enabled full-time headset operation on your telephone. Telephones with full-time headset operation enabled must be operated only with headsets. A headset can be used either in regular answer mode or with the Auto Answer feature programmed.

Most headsets are installed using the same jack that the handset plugs into. When the telephone is not in use, lift the handset from the cradle and carefully turn the telephone upside down. Unplug the handset cord where it connects to the telephone. Plug in the headset cord in the same place. Store your handset in a safe place. Unplug the headset cord where it connects to the telephone. Plug in the handset cord in the same place. Set the telephone upright and return the handset to the cradle.

Store your headset in a safe place. Installation will disable your handset microphone. Disconnecting the headset at the jack or at the quick-disconnect plug restores handset operation. Plug the headset cord into the headset jack the jack nearest the front of the telephone.

To enable or disable headset operation for headsets on telephones that are not programmed for full-time headset operation:. To hang up:. Your system administrator should have assigned you an identification number.

Your identification number allows you to access the ACD system. Enter your identification number. If you hear dial tone you have logged out successfully. Welcome to ManualMachine.